Click Rate analysis software-Century Wisdom (Suzhou) Testing Technology Co., Ltd

English

Home page

Product

EMC Testing Solution Provider

Click Rate analysis software

Brand:

ROHDE&SCHWARZ

Product Description
Main features
Technical parameters

- Commodity name: Click Rate analysis software
- Commodity ID: 1064826815844601856
- 品牌11: ROHDE&SCHWARZ
- 描述: Suitable for EMI testing receiver R&S ® ESW, R&S ® ESU, R&S ® ESR and R&S ® ESCI's click through rate analyzer.
- 品牌: ROHDE&SCHWARZ
　　Click rate analyzers for EMI test receivers R&S ESW, R&S ESU, R&S ESR and R&S ESCI.

　　In combination with R&S ESW and R&S ESR EMI test receivers, 4-channel operation is possible. With R&S ESU and R&S ESCI EMI test receivers, the click-through analyzer software is limited to one channel.

　　The software performs click-through rate analysis according to CISPR 16-1-1 and CISPR 14-1 / EN 55014-1. The software displays the maximum and quasi-peaks graphically in real time. After the measurement, the test report can be displayed and printed.
　　Complies with CISPR 14-1:2005/EN 55014:2006 and CISPR 14-1:2016/EN 55014-1:2016

　　The VISA (Virtual Instrumentation Software Architecture) universal interface is used to communicate via LAN or IEC/IEEE bus interfaces

　　Real-time graphical representation of measured values

　　Compatible with the R&S ESR and R&S ESW 4 channel standards for parallel click-through analysis at 150 kHz, 500 kHz, 1.4 MHz and 30 MHz

　　Precise measurement of click duration using a peak detector and a temporal resolution of 500 μs or less using a quasi-peak detector determination of flexibility

　　Click count and CTR calculation

　　Exceptions to the standard are allowed

　　Remote control of R&S ENV216, R&S ENV432, R&S ENV4200, R&S ESH2-Z5, and R&S ESH3-z5 V-network (LISN)

　　Generate a detailed test report and print it on your Windows default printer

　　Electronic archiving of measurements

PCrequest
operating system	Microsoft Windows XP/7/10
Regional and language settings	English (non-Unicode)
Usually required	Intel Core or compatible models; 2 GB RAM; 12 MB of available hard disk space for software installation; Up to 480 megabytes for storing results in a two-hour measurement session
interface	LAN or IEC/IEEE bus (GPIB) interface
Software requirements	10 dB/m (± 2 dB)
GPIBcontrol	IS VISA 3.2 / IS GPIB 2.10
LANcontrol	NI VISA 3.2 / RSIB Passport 1.4
Device requirements
R&S®ESR 4Channel measurement	Receiver firmware version 2.27 or later; R&S®ESR-B50 hardware option for time domain and real-time analysis
R&S®ESW 4Channel measurement	Receiver firmware version 1.20 SP1 or later
1Channel measurement	▪ R&S ESW with firmware version 1.10 or later ▪ Firmware version 2.26 or later R&S ESR, but without option R&S ESR-B50 ▪ R&S ESU with firmware version 3.93 or later ▪ The firmware version is 3.32 SP3 or later R&S®ESCI

Operating steps:
Start the software (Figure 1)
software configuration
Measurement parameter settings (Figure 2)
Channel parameter settings (Figure 3)
Click through rate parameter settings (Figure 4)
LISN parameter settings (Figure 5)
Measurement menu settings
General settings (Figure 6)
Report Settings (Figure 7)
RS printer (PDF) settings (Figure 8)
Run the software (Figure 9, Figure 10)
Analysis and testing reports
Software Window Report (Figure 11)
Print a simple report (Figure 12)

start software (figure 1)
Measurement parameter settings (figure 2)
Channel parameter setting (image 3)
CTR parameter setting (Figure 4)
LISN parameter setting (Figure 5)
General settings (Figure 6)
Report Settings (Figure 7)
RS Printer (PDF) Settings (Figure 8)
run the software (Figure 9)
run the software (Figure 10)
Software Windows report (Figure 11)
Print simple reports (Figure 12)